two-doberman-puppies-left-for-sale2 dobermann-puppies-for-sale

Doberman litter news, when will your future puppy be ready to pickup?

Important Tips From A Handyman On How To Construct A Dog House

By Mick, Oct 23 2018 12:00PM

The elements of weather can be harsh and having a roof over your head is something very important. The dogs that we have in our homes also need shelter. Even though they may be furry, their coat of fur does not provide sufficient protection from the elements. To ensure a dog lives comfortably, they need to have a good house that is of the right size.



• Circular saw or hand saw

• Electric jig saw

• Power drill and bits

• Carpenters square

• Claw hammer

• Measuring tape or ruler and pencil

• Caulking gun

• Exterior grade plywood sheets

• Treated pine

• Silicone sealant and construction grade adhesive

• Galvanized nails and bolts

• Steel Colourbond roofing,

• clout nails and insulation (optional)


1. Have a plan

Dog houses come in various sizes and you need to construct a house that will perfectly fit your dog. It should not be too small as the dog will face difficulties when making simple movements standing up or even curling up for a nap. On the other hand, if the house is too big, the dog may feel insecure. Getting the size right is therefore very crucial.

2. Start at the bottom

Building a dog house should be systematic and the ideal approach is to start from the bottom. Construct the floor and then work up. As per the recommended standards, the floor should be raised 100mm from the ground. This is to allow for air circulation and prevent runoff water from entering the kennel.


The sub-floor frame should be built using 100 x 50mm frames of treated pine. Pine is ideal for use in this case as it is resistant to rotting. Precision is very important at this stage and measurements should be made using a pencil and a carpenter's square on the pieces of timber to be used. When cutting the ends of the timber, they should be square in shape to ensure that the joints are strong. The Centre subfloor timber frame piece should then be cut and nailed to the outside piece at an angle.

The same process should then be repeated for the other two small cross pieces. Holes should then be drilled through the subfloor frame to allow for ventilation and also facilitate the runoff of water from the floor of the kennel. To finalize on the base, measure and cut a 12mm piece of plywood and attach it to the frame by using a combination of adhesive and fixing the sides of the cross pieces with galvanized nails.

3. Construction of the door and walls

Before constructing the door, one needs to establish the position and size of the door before the walls are set up. In our mitri plan, one can get exact measurements of the various door sizes.


The sides wood pieces should be measured and cut in such a manner that they flush with the frame edge. The ends of the walls should have strong butt joints. As per the design, the front and back walls should overhang and flush with the plywood. The construction should be done using adhesives and 40mm by 2mm galvanized nails with bullet heads.

4. Roofing

Roofing should only be done after walling is complete. The roof should be made of plywood. Waterproofing should be done by adding a layer of iron sheet, paint or even Astroturf on top of the plywood. As a safety precaution when using corrugated iron, all the edges and corners should always be rounded.

Roof installation and finishes

The mitre plan provides all the relevant information that one requires when cutting the gable, procedures for holding up the roof panel and the ideal height of the apex. The back wall should always be measured from the outside.

For a start, one can temporally attach the gable by nailing in a scrap bit of plywood to the gable using nails. This will make the gable ready for installation of the roof panels

Roof sheets should always be cut in such a manner that they are 12mm longer than each other. This will allow enough thickness of the plywood and create the perfect butt joint at the ridge. The extra length will also make the roof overhang over the plywood and prevent water from spilling over the door. The ideal length of overhang for the kennel should be 125mm. To keep the joints watertight, silicon should be used.

Even with the right set of tools and an elaborate instruction to guide you, constructing a dog house can prove to be a daunting task especially when one is not conversant with carpentry works. Hiring a handyman to do the job for you in such situations is a wise idea. It may cost you financially but save you time and the hustle of pinning the pieces of timber together.

Add a comment
* Required

Find out more about your puppy

Doberman puppy help separation-anxiety-in-a-young-doberman-puppy